WIC-1B-U-V2 Cisco 1-Port WAN Interface Card | Refurbished

Description

Features and Specifications

The WIC-1B-U-V2 is a 1-port WAN (Wide Area Network) Interface Card manufactured by Cisco Systems, a leading provider of networking solutions. This interface card is designed for use in Cisco Integrated Services Routers (ISRs) and provides a single WAN connection for remote office or branch office (ROBO) networks.

Some of the features and specifications of the WIC-1B-U-V2 are as follows:

• Interface type: The WIC-1B-U-V2 interface card is a High-Speed Serial Interface (HSSI) card, which supports speeds of up to 52 Mbps.
• WAN connectivity: The card supports a range of WAN connectivity options, including T1/E1, fractional T1/E1, and symmetric DSL (SDSL) connections.
• Compatibility: The WIC-1B-U-V2 interface card is compatible with a range of Cisco Integrated Services Routers, including the 1700, 1800, 2600, 2800, 3600, and 3700 series routers.
• Hot-swappable: The card is hot-swappable, which means it can be installed or removed from a router without powering down the router.
• LEDs: The card features LEDs that provide status information, including link activity, port status, and error conditions.
• Dimensions: The WIC-1B-U-V2 measures 3.1 x 3.1 x 0.8 inches and weighs 3.2 ounces.
• Power consumption: The card consumes approximately 3 watts of power.
• Operating temperature range: The card operates in a temperature range of 32°F to 104°F (0°C to 40°C) and a relative humidity range of 10% to 85% (non-condensing).

Compatibility with Cisco routers and network Modules

The WIC-1B-U-V2 is a 1-Port WAN (Wide Area Network) Interface Card manufactured by Cisco Systems. It is designed to provide WAN connectivity to Cisco routers and network modules.

This interface card is compatible with a variety of Cisco routers, including Cisco 1700 Series routers, Cisco 1800 Series routers, Cisco 2600 Series routers, Cisco 2800 Series routers, and Cisco 3700 Series routers. It is also compatible with a number of network modules, including the Cisco NM-1FE1R2W, NM-1FE2W, NM-2FE2W, NM-1FE1R2W, and NM-2W.

The WIC-1B-U-V2 interface card supports a range of WAN protocols, including Frame Relay, High-Level Data Link Control (HDLC), Point-to-Point Protocol (PPP), and Serial Line Internet Protocol (SLIP). It also supports a range of speeds, including 56 Kbps, T1/E1, and fractional T1/E1.

Installation and Configuration

The WIC-1B-U-V2 is a 1-Port WAN Interface Card designed for use in Cisco Integrated Services Routers (ISR). It provides a single synchronous serial connection with speeds up to 2.048 Mbps, making it ideal for connecting to WAN networks using T1, E1, or J1 lines.

To install and configure the WIC-1B-U-V2 card, follow these steps:

• Power off the router and unplug it from the power source.
• Remove the router cover to access the internal components.
• Locate an available WIC slot on the router motherboard and gently slide the WIC-1B-U-V2 card into the slot.
• Use the mounting screw to secure the card in place.
• Reattach the router cover and reconnect the power source.

After installing the WIC-1B-U-V2 card, you can configure it using the Cisco IOS command-line interface (CLI). The following steps will guide you through the configuration process:

• Connect to the router console using a terminal emulator program such as HyperTerminal or PuTTY.
• Enter the IOS command to enter global configuration mode:router# configure terminal
• Configure the serial interface by specifying the interface type, slot number, and port number:router(config)# interface serial 0/0/0
• Set the line encoding to the appropriate type (e.g. T1, E1, or J1):router(config-if)# line-code {ami | b8zs | hdb3}
• Set the framing type to the appropriate type (e.g. SF or ESF):router(config-if)# framing {sf | esf}
• Set the clocking source to internal or external:router(config-if)# clock source {internal | line}
• Configure the IP address and subnet mask for the interface:router(config-if)# ip address <address> <subnet-mask>
• Enable the interface:router(config-if)# no shutdown
• Save the configuration changes:router# copy running-config startup-config

Once you have completed these steps, the WIC-1B-U-V2 card should be fully installed and configured for use with your Cisco router.

General Information

• Manufacturer: Cisco Systems, Inc
• MPN: WIC-1B-U-V2
• Product Name: 1-Port ISDN BRI WAN Interface Card
• Product Type: WAN Interface Card (WIC)
• SKU: WIC-1B-U-V2

Technical Information

• Application/Usage: Wide Area Network

Interfaces / Ports

• Interfaces/Ports: 1 x ISDN BRI (U) WAN
• Interfaces/Ports Details: 1 x RJ-45 ISDN BRI (U) WAN

Controls / Indicators

• Status Indicators-
• Network module status indicator
• Status LEDs for each B Channel and NT1

Environmental Conditions

• Temperature: 32°F (0°C) to 104°F (40°C) Operating
• Temperature: -13°F (-25°C) to 158°F (70°C) Storage
• Humidity: 5% to 95% Non-condensing Relative Humidity

Dimensions & Weight

• Width: 3.1 Inch
• Depth: 4.4 Inch
• Height: 0.8 Inch
• Weight: 112.80 Oz

Miscellaneous

• Maximum Number of Modules per Chassis:
• Cisco 1720 and 1721: 2
• Cisco 1750: 2
• Cisco 1751 and 1760: 2
• Cisco 2600XM: 4
• Cisco 3620: 4
• Cisco 3640: 8
• Cisco 3660: 12
• Cisco 2691: 5
• Cisco 3725: 7
• Cisco 3745: 11

Compatibility

• Cisco 1700 Series
• Cisco 2600 Series
• Cisco 3600 Series
• Cisco 3700 Series