Description
Introduction to 8TB-7.2K RPM
The MB008000GWJRT HPE 8TB 7.2K RPM SATA 6GBPS 3.5inch LFF 512E Hard Drive is a type of hard drive used for data storage in servers and other computing systems. The 8TB capacity means it can store a large amount of data, while the 7.2K RPM (rotations per minute) speed enables faster data access and transfer.
The higher the RPM, the faster the hard drive can read and write data, resulting in better performance. The 7.2K RPM speed is considered a good balance between performance and cost-effectiveness for many server applications.
In addition, this hard drive uses the SATA 6Gbps interface, which offers high-speed data transfer rates between the hard drive and the host system. This interface is widely used in servers and other storage systems, providing a reliable and efficient connection for data transfer.
Installation and Configuration
Installation and configuration of the MB008000GWJRT HPE 8TB hard drive involves the following steps:
- Ensure compatibility: Before installing the hard drive, ensure that it is compatible with your server or storage system. Check the documentation for your system or contact the vendor for assistance.
- Prepare the system: Shut down the server or storage system and unplug it from the power source. Open the system enclosure and locate an empty drive bay for the hard drive. Remove any mounting brackets or filler panels that may be in place.
- Install the drive: Carefully insert the hard drive into the empty bay, making sure it is properly seated and securely fastened with screws or other hardware provided by the manufacturer.
- Connect cables: Locate the SATA data and power connectors on the hard drive and connect them to the corresponding ports on the system board or RAID controller. Make sure the connectors are properly aligned and securely fastened.
- Configure the drive: Depending on your system and operating system, you may need to configure the hard drive in the BIOS or other system settings to ensure it is recognized and properly configured for use. Follow the instructions provided by the system vendor or operating system documentation.
- Initialize and format the drive: Once the hard drive is recognized by the system, you may need to initialize and format it to prepare it for use. This can typically be done through the operating system’s disk management tools or other system utilities. Follow the instructions provided by the vendor or documentation for your operating system.
- Verify operation: Once the hard drive is installed, configured, and formatted, verify that it is operating correctly by running diagnostic tests or performing other system checks as recommended by the vendor.
Energy Efficiency
The MB008000GWJRT HPE 8TB hard drive is designed with energy efficiency in mind. It consumes less power than traditional hard drives, making it an environmentally-friendly choice that can also save money on energy costs.
The drive uses the SATA 6Gbps interface, which is known for its high data transfer rates and low power consumption. It also features a 7.2K RPM speed, which provides a balance between performance and power consumption. The 3.5 inch large form factor (LFF) allows for greater capacity and reduces the number of drives needed, resulting in less power consumption.
In addition, the drive incorporates advanced power management features, such as idle power savings and power-on-demand, which allow the drive to use less power when it is not actively accessing data. The drive also uses a low-power consumption mode when it is not in use for an extended period of time.
General Information
- Manufacturer: HPE
- MPN: MB008000GWJRT
- Type: Internal Hard Drive (HDD)
- HDD Type: SATA-6GBPS
- SKU: MB008000GWJRT
- Option Part Number: 819203-B21
- Spare Part Number: 820033-001
- Assembly Part Number: 877683-002
Technical Information
- Device Type: Hard Drive Hot-Swap
- Capacity: 8 TB
- Form Factor: 3.5 inch LFF
- Interface Type: SATA-6GBPS
- Bytes per Sector: 512
- Drive Technology (Fill): Air
- Plug Type: Hot Plug
- Format Type: 512e
- Carrier Type: Smart Carrier (SC)
- Workload Type: Midline
- Features: Native Command Queuing (NCQ), Advanced Format 512e
- Bundled with: HPE SmartDrive carrier
Performance
- Drive Transfer Rate: 6 GB/SEC (External)
- Average Seek Time: 8.5 Ms
- Max Seek Time: 15.7 Ms
- Track-to-Track Seek Time: 0.7 Ms
- Spindle Speed: 7200 RPM
- Max Sequential Throughput (MiB/S): 230
- 128Kib Random Read (IOPs): 105
- 128Kib Random 70% RD/ 30% WT (IOPs): 110
- 128Kib Random 50% RD/ 50% WT (IOPs): 115
Power
- Idle Time: 8.8 Watt
- Random R/W: 12.1 Watt
- Sequential Read: 10.8 Watt
- Sequential Write: 10.5 Watt
Dimension and Weight
- Width : 4 Inch
- Depth : 5.8 Inch
- Height : 1 Inch
- Weight : 1.52 Lbs
Environmental Parameters
- Min Operating Temperature: 50 °F
- Max Operating Temperature: 95 °F
Compatibility Information
- HPE ProLiant DL Series: DL180 Gen9 (3.5 inch), DL180 Gen9 Base (3.5 inch), DL180 Gen9 Entry (3.5 inch), DL180 Gen9 Storage (3.5 inch), DL20 Gen9 Solution (3.5 inch), DL360 Gen10 (3.5 inch), DL360 Gen10 Base (3.5 inch), DL360 Gen10 Entry (3.5 inch), DL360 Gen10 High Performance (3.5 inch), DL360 Gen10 Low (3.5 inch), DL360 Gen10 Performance (3.5 inch), DL360 Gen10 Solution (3.5 inch), DL380 Gen10 (3.5 inch), DL380 Gen10 Base (3.5 inch), DL380 Gen10 Entry (3.5 inch), DL380 Gen10 High Performance (3.5 inch), DL380 Gen10 Performance (3.5 inch), DL380 Gen10 Solution (3.5 inch), DL385 Gen10 (3.5 inch), DL385 Gen10 Base (3.5 inch), DL385 Gen10 Entry (3.5 inch), DL385 Gen10 High-Performance (3.5 inch), DL385 Gen10 Performance (3.5 inch), DL385 Gen10 Solution (3.5 inch), DL388 Gen9 (3.5 inch), DL388 Gen9 Base (3.5 inch), DL80 Gen9 Entry (3.5 inch)
- HPE ProLiant ML Series: ML110 Gen9 (3.5 inch), ML110 Gen9 Base (3.5 inch), ML110 Gen9 Entry (3.5 inch), ML30 Gen9 Entry (3.5 inch), ML30 Gen9 Solution (3.5 inch)
