Description
Memory capacity and speed
Memory capacity and speed are two important factors that determine the performance of a RAM module. The P11444-091 HPE 32GB 3200Mhz PC4-25600 DDR4 SDRAM Cl22 Ecc Reg 288-Pin Ram, has a capacity of 32GB, which is the amount of memory that the module can store. The higher the capacity, the more data the module can hold, which can improve performance and multitasking capabilities of the system.
The speed of the RAM, measured in MHz, refers to the rate at which the memory module can transfer data. The P11444-091 HPE RAM has a speed of 3200MHz, which is relatively fast compared to other RAM modules on the market. This high speed allows for faster data transfer and improved system performance, particularly in applications that require fast memory access such as gaming, video rendering and other high-performance tasks.
It’s important to note that the memory capacity and speed of the P11444-091 HPE RAM are optimized to work with the latest server and workstation platforms that support the DDR4 memory technology and ECC memory. This RAM model will be able to provide the best performance and reliability in those platforms, it’s also important to check if your system supports the memory speed and capacity before purchasing.
Memory type and pin configuration
The P11444-091 HPE 32GB 3200Mhz PC4-25600 DDR4 SDRAM Cl22 Ecc Reg 288-Pin Ram is a type of DDR4 SDRAM (Synchronous Dynamic Random-Access Memory). DDR4 is the latest generation of RAM technology and is faster and more efficient than its predecessor, DDR3. It is also capable of running at higher speeds and has a higher memory capacity.
The pin configuration for the P11444-091 HPE RAM is 288-Pin, which is the standard for DDR4 memory modules. The 288-pin design is an improvement over the 240-pin design used in DDR3 memory, as it allows for more memory capacity and higher data transfer rates. Additionally, the 288-pin design allows for a more efficient power consumption, which can help to reduce heat and extend the lifespan of the memory module.
It’s also important to note that the P11444-091 HPE RAM is ECC memory, which means that it has Error Correction Code (ECC) support built-in. ECC memory uses an extra memory bit for each byte of data to detect and correct errors that may occur during data transfer, this is important feature for high-performance systems that require high data integrity and reliability such as servers and workstations.
Installation and setup guide
Installing and setting up the P11444-091 HPE 32GB 3200Mhz PC4-25600 DDR4 SDRAM Cl22 Ecc Reg 288-Pin Ram is a relatively straightforward process, but it’s important to follow the correct steps to ensure a successful installation and to avoid damaging the memory module or the system.
Here is a general guide on how to install and set up the P11444-091 HPE RAM:
- Before installing the memory module, make sure to turn off the system, unplug the power cord, and remove the battery to prevent any accidental power on during the installation process.
- Locate the memory slots on the motherboard. On most systems, the memory slots will be located near the CPU.
- Carefully align the memory module with the memory slot, making sure that the notches on the memory module match the notches on the memory slot.
- Gently press the memory module into the slot until it clicks into place.
- Once the module is seated, power on the system, and enter the system BIOS or UEFI to verify that the new memory module is recognized by the system.
- Configure the memory settings in the BIOS/UEFI to match the specifications of the memory module. This will typically involve setting the memory speed, voltage, and memory timing settings.
- Save the settings and exit the BIOS/UEFI, and then reboot the system.
- Once the system has booted, check the system properties or run memory diagnostic software to confirm that the new memory module has been correctly installed and is functioning correctly.
It’s important to note that these steps may vary depending on the specific system and motherboard that you are using, so refer to the system and motherboard documentation for specific instructions.
Additionally, you should always handle the memory module with care to avoid static discharge and other physical damage, and make sure to use the correct memory module for your system to avoid compatibility issues.
General Information of this HPE P11444-091
- Brand Name: HPE
- Model Number or SKU# P11444-091
- Type: Memory (RAM)
- RAM Type: PC4-25600
- Product Name: HPE Smart Memory 32GB-DDR4-dimm-288-Pin-Registered Memory Module
Technical Information about HPE DDR4 32GB Ram
- Storage Capacity: 32GB
- Memory Type: Ddr4 Sdram Dimm 288-Pin
- Number Of Modules: 1 X 32GB
- Memory Speed: 3200mhz (PC4-25600)
- Features: Dual Rank X4, Registered
- Error Checking: Ecc
- Voltage: 1.2 V
- Latency Timings: Cl22
- Upgrade Type: System Specific
- Device Supported: Server
Physical Characteristics of HPE P11444-091
- Dimensions (W X D X H) : 8.89 X 19.81 X 1.91 Cm (3.5 X 7.8 X 0.75 In)
- Weight: 0.45 Kg (1 Lb)
Compatibility of DDR4 32GB Ram
- Proliant Dl325 Gen10 Plus, Dl385 Gen10 Plus, Dl385 Gen10 Plus Entry
Contact us or ask for live chat/help if you have any questions about the compatibility of this item to ensure the model’s matching features with your current system.
