Description
Compatibility with NetApp Systems
The compatibility of the X6599A-R6 with NetApp systems will depend on several factors, including the operating system version, storage array firmware version, and the specific NetApp system model.
To ensure compatibility, it is recommended to check the compatibility matrix provided by the manufacturer of the X6599A-R6, as well as the compatibility information available from NetApp’s website.
If the X6599A-R6 is being used as a replacement drive for an existing NetApp system, it is important to verify that the replacement drive is compatible with the existing system before installation.
It is also important to follow the manufacturer’s instructions for installing and configuring the X6599A-R6 in a NetApp system, to ensure that it functions correctly and provides optimal performance.
Operating Environment Requirement
Here are some general operating environment requirements for the X6599A-R6:
- Operating temperature: The device should be operated within the temperature range specified by the manufacturer, typically between 0°C and 35°C.
- Operating humidity: The device should be operated within the relative humidity range specified by the manufacturer, typically between 20% and 80% non-condensing.
- Altitude: The device should be operated at altitudes within the range specified by the manufacturer, typically up to 3,000 meters.
- Power requirements: The device should be operated within the voltage and current specifications specified by the manufacturer, typically between 100 and 240V AC and 50-60Hz.
- Environmental factors: The device should be protected from exposure to extreme temperature fluctuations, moisture, dust, corrosive substances, and electromagnetic interference.
- Physical shock and vibration: The device should be protected from physical shock, vibration, and rough handling during installation, operation, and transportation.
Technical Specifications of X6599A-R
The technical specifications of the X6599A-R6 will depend on the specific model and manufacturer. However, here are some common specifications that may be included:
- Capacity: The capacity of the device, typically measured in terabytes (TB) or gigabytes (GB).
- Form factor: The physical form factor of the device, such as 2.5-inch or 3.5-inch.
- Interface: The type of data interface supported by the device, such as SAS, SATA, or NVMe.
- Data transfer rate: The maximum data transfer rate supported by the device, typically measured in gigabits per second (Gbps) or megabytes per second (MB/s).
- Latency: The average time it takes for the device to access data, typically measured in milliseconds (ms).
- Seek time: The time it takes for the device to access a specific data block, typically measured in milliseconds (ms).
- Error rate: The rate at which errors occur during data transfer, typically measured as non-recoverable errors per bits read.
- MTBF: Mean time between failures, a measure of the expected reliability of the device, typically measured in hours.
- Power consumption: The average power consumption of the device, typically measured in watts (W).
- Operating temperature: The temperature range within which the device can be operated, typically between 0°C and 35°C.
Data Transfer Capabilities and Distance Support
The data transfer capabilities and distance support of the X6599A-R6 will depend on several factors, including the interface type, cable type, and the specific system configuration.
- Interface type: The data transfer rate and distance support will depend on the type of data interface used, such as SAS, SATA, or NVMe. For example, SAS interfaces typically support data transfer rates of up to 12 Gbps and distances of up to 10 meters, while NVMe interfaces typically support higher data transfer rates and shorter distances.
- Cable type: The data transfer rate and distance support will also depend on the type of cable used to connect the device to the system. For example, SAS cables typically support data transfer rates of up to 12 Gbps and distances of up to 10 meters, while NVMe cables typically support higher data transfer rates and shorter distances.
- System configuration: The overall data transfer capabilities and distance support will also depend on the specific system configuration, including the type and number of devices connected, the controller used, and the software configuration.
It is important to consult the manufacturer’s manual and follow the manufacturer’s guidelines for configuring the X6599A-R6 in a system to ensure optimal data transfer capabilities and distance support.
X6599A-R6 NetApp 850NM 10G Sfp+ Sr Transceiver.
