P05928-X21 HPE 480GB DS SATA-6GBPS 2.5Inch Read Intensive New

Endurance and reliability are important characteristics of any storage device, including the HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive.

Endurance refers to the ability of the SSD to withstand frequent write operations without degrading or wearing out. The endurance of an SSD is typically measured in terms of the total amount of data that can be written to the drive over its lifetime, often referred to as the drive's "terabytes written" (TBW) rating. The HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive is a "read-intensive" SSD, which means it is designed for workloads where data is mostly read from the drive, rather than written. As such, it has a relatively high endurance rating of up to 310 terabytes written (TBW), which means it can withstand a large amount of write activity without wearing out.

Reliability refers to the stability and consistency of the drive's performance over time, as well as its ability to protect data against loss or corruption. The HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive is designed with features that help ensure data reliability and protection, such as end-to-end data path protection, power loss protection, and wear leveling. These features help to prevent data loss or corruption, and ensure that the drive's performance remains consistent and reliable over its lifetime.

Installation and configuration of the HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive involves physically installing the drive into a compatible system and setting up the necessary configurations to make it operational.

Here are the steps involved in installing and configuring the HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive:

• Turn off the computer or server and unplug all cables and accessories.
• Locate an available drive bay and remove any existing drive or bracket.
• Install the HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive into the drive bay and secure it using screws or brackets provided.
• Connect the SATA cable to the drive and the motherboard or RAID controller.
• Connect the power cable to the drive and the power supply unit (PSU).
• Close the computer case and plug in all cables and accessories.
• Power on the computer or server.
• Enter the system BIOS to ensure that the system recognizes the new drive. If necessary, configure the BIOS settings to boot from the new drive.
• Once the system boots up, install the necessary device drivers and software, if applicable.
• Initialize and format the drive using the operating system or storage management software. You may need to create partitions, assign drive letters, and set other configurations.

It's important to note that the exact installation and configuration process may vary depending on the system and operating system you are using. Therefore, it's important to consult the user manual or online resources for specific instructions related to your particular system.

Additionally, it's recommended to back up important data before making any changes to the system, and to ensure that the system meets the necessary hardware and software requirements to support the HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive.

The HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive Solid State Drive (SSD) has several data protection and security features designed to help protect your valuable data.

• Self-Encrypting Drive (SED) - The HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive SSD supports hardware-based AES 256-bit encryption to protect data-at-rest. This feature ensures that data is secured even if the drive is lost or stolen.
• Data Encryption - The drive also features enhanced data encryption and security features to protect your data. This includes secure erase, instant secure erase, and firmware-based password protection.
• End-to-End Data Protection - The HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive SSD supports end-to-end data protection, which helps ensure that data is not corrupted during transmission between the host and the drive.
• Power Loss Protection - The SSD has a power loss protection feature, which ensures that any data in the drive's cache is written to the NAND flash memory in the event of a power loss. This helps prevent data loss or corruption during sudden power outages.
• Wear Leveling and Over-Provisioning - The drive uses advanced wear-leveling algorithms that evenly distribute data across the drive to extend its lifespan. Additionally, the HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive SSD has a percentage of over-provisioning built-in, which helps improve performance and increase endurance.
• Compliance and Certification - The HPE 480GB DS SATA-6GBPS 2.5 Inch Read Intensive SSD has several certifications and compliances, including FIPS 140-2 validation, Common Criteria, TAA compliance, and others. These certifications and compliances provide assurance that the SSD meets the highest security standards for various industries and organizations.

• Manufacturer Name : HPE
  
• MPN: P05928-X21
• Type: Internal Hard Drive
• SSD Type: SATA 6 GBPS
• SKU : P05928-X21
• Spare Part Number: P08567-001

• Device Type: Solid State Drive - Hot-Swap
  
• Capacity: 480GB
• Form Factor: 2.5 inch SFF
• Interface: SATA 6Gbps
• NAND Flash Memory Type: Triple-level cell (TLC)
• Plug Type: Hot Pluggable
• Connectivity Type: Single
• Carrier Type: Smart Carrier (SC)
• Workload Type: Read Intensive
• Bundled with: HPE SmartDrive Carrier (SC)
• Features: Digitally Signed Firmware (DS)
• Platform Supported: HPE ProLiant Rack/Tower/BladeSystem Servers/Synergy
• Height: 7.00 mm(0.30 inch)

• Lifetime Writes (TB): 1200
  
• Endurance DWPD (Drive Writes Per Day): 1.30
• Drive Transfer Rate: 6 GBps (external)
• MAX Seq. Reads Throughput (MiB/s): 530
• MAX Seq. Writes Throughput (MiB/s): 465
• Random Read Average Latency uSec (4KiB,Q1): 110
• Random Write Average Latency uSec (4KiB,Q1): 75
• Random Read IOPS (4KiB, Q=16): 68000
• Random Write IOPS (4KiB, Q=16): 17500
• MAX Random Read IOPS (4KiB): 76000@Q32
• MAX Random Write IOPS (4KiB): 19000@Q4

• Idle Time: 1.27 Watt
  
• Random Read: 2.92 Watt
• Random Write: 2.92 Watt
• Sequential Read: 2.26 Watt
• Sequential Write: 3.15 Watt
• Random Read/Write: 2.92 Watt
• MAX: 4.00 Watt

• Min Operating Temperature: 32 °F
• Max Operating Temperature: 140 °F

Dimensions & Weight

• Height: 0.63 Inch
  
• Width: 3.10 Inch
• Depth: 5.45 Inch
• Weight: 1.50 Lbs

• HPE Apollo Series: 4200 Gen9 for Google (2.5 inch)
  
• HPE ProLiant DL Series: DL180 Gen10 (2.5 inch), DL180 Gen10 Entry (2.5 inch), DL180 Gen10 SMB (2.5 inch), DL325 Gen10 (2.5 inch), DL325 Gen10 Base (2.5 inch), DL325 Gen10 Entry (2.5 inch), DL325 Gen10 Performance (2.5 inch), DL325 Gen10 Plus (2.5 inch), DL325 Gen10 SMB Solution (2.5 inch), DL325 Gen10 Solution (2.5 inch), DL360 Gen9 (2.5 inch), DL360 Gen9 Base (2.5 inch), DL360 Gen9 CMS (2.5 inch), DL360 Gen9 Entry (2.5 inch), DL360 Gen9
• Performance (2.5 inch), DL360 Gen9 Special Server (2.5 inch), DL380 Gen10 (2.5 inch), DL380 Gen10 All Flash Server for Datera (2.5 inch), DL380 Gen10 Base (2.5 inch), DL380 Gen10 Entry (2.5 inch), DL380 Gen10 Entry SMB (2.5 inch), DL380 Gen10 for Cohesity DataPlatform (2.5 inch), DL380 Gen10 High Performance (2.5 inch), DL380 Gen10 Hybrid Server for Datera (2.5 inch), DL380 Gen10 Network Choice (2.5 inch), DL380 Gen10 Network Choice for CTERA
• (2.5 inch), DL380 Gen10 Network Choice for SAP HANA Compute Block (2.5 inch), DL380 Gen10 Performance (2.5 inch), DL380 Gen10 Server for CTERA (2.5 inch), DL380 Gen10 SMB (2.5 inch), DL380 Gen10 SMB Networking Choice (2.5 inch), DL380 Gen10 Solution (2.5 inch), DL388 Gen10 (2.5 inch)