Description
Power Input and Output
The Cisco NCS 4200 Series AC Power Supply (NCS4K-AC-PSU) is a 3000 watt AC power module designed for use with the Cisco Network Convergence System 4200 Series. The power input for the module is 100-240VAC, 50-60Hz, which means it can accept a wide range of voltage inputs, and it can operate with different frequencies of 50Hz or 60Hz. The output of the power supply is -48VDC at 62.5A, which means it provides a negative 48-volt DC output at a current of 62.5 amperes. The module is designed to provide power to the system and can be used as either a primary or redundant power source. It also has built-in power supply redundancy feature which allows for a second power supply to be installed for redundancy in case of a failure.
Installation and Configuration
The installation and configuration of the Cisco NCS 4200 Series AC Power Supply (NCS4K-AC-PSU) 3000 watt AC power module can be done in the following steps:
- Prepare for installation: Before installing the NCS4K-AC-PSU, ensure that the system is powered off and disconnected from the power source. Also, check that the ambient temperature is within the specified range and that the power supply is compatible with the system.
- Install the power supply: To install the NCS4K-AC-PSU, slide the power supply into the chassis and secure it with the thumbscrews. Connect the power cord to the power supply and the power outlet.
- Configure the power supply: Once the power supply is installed, it can be configured using the Cisco Network Convergence System 4200 Series command-line interface (CLI) or the web-based graphical user interface (GUI).
- Power on the system: After the power supply is installed and configured, power on the system and check that the power supply is operating correctly.
- Monitor the power usage: Monitor the power usage of the system and make adjustments as needed to reduce power consumption.
- Configure Power Redundancy: If you have more than one power supply installed, you can configure power redundancy feature. This feature allows a second power supply to be installed for redundancy in case of a failure.
- Verify Power supply status: Verify the power supply status via the CLI or GUI, to ensure that the power supply is functioning properly and providing stable and consistent power to the system.
It’s important to follow the instructions and guidelines provided by the manufacturer for the proper installation and configuration of the NCS4K-AC-PSU. It’s also recommended to check the compatibility of the power supply with the device it’s powering to avoid any potential damage to the device.
Maximizing Energy Efficiency
Maximizing energy efficiency of the Cisco NCS 4200 Series AC Power Supply (NCS4K-AC-PSU) 3000 watt AC power module involves implementing best practices to reduce power consumption and increase the efficiency of the power supply. Some of the ways to achieve this include:
- Using the power supply in combination with other energy-efficient devices and systems, such as Energy Efficient Ethernet (EEE) to reduce power consumption during periods of low network activity.
- Using the power supply in a cool and well-ventilated area to ensure proper cooling and reduce the need for additional cooling systems.
- Keeping the power supply clean and free of dust to prevent overheating.
- Using the built-in power supply redundancy feature to ensure that the system can continue to operate even if one of the power supplies fails.
- Monitoring the power usage of the system and making adjustments as needed to reduce power consumption.
- Using power management features such as power capping or dynamic power scaling to reduce the overall power consumption.
- Using a power supply with a high efficiency rating, such as 80 Plus, to ensure that less energy is wasted as heat.
- Using a power supply that can be shut off or put into standby mode when not in use, to reduce power consumption.
By implementing these best practices, organizations can optimize the energy efficiency of the Cisco NCS 4200 Series AC Power Supply and reduce power consumption, resulting in cost savings and environmental benefits.
Features and Benefits
The Cisco NCS 4200 Series AC Power Supply (NCS4K-AC-PSU) is a 3000 watt AC power module designed for use with the Cisco Network Convergence System 4200 Series. Some of the features and benefits of the NCS4K-AC-PSU include:
- High Power Output: The NCS4K-AC-PSU provides a high power output of 3000 watts, making it suitable for powering large network systems.
- Wide Input Voltage Range: The NCS4K-AC-PSU can accept a wide range of voltage inputs (100-240VAC, 50-60Hz), making it suitable for use in different regions and environments.
- Power Supply Redundancy: The module has built-in power supply redundancy feature which allows for a second power supply to be installed for redundancy in case of a failure.
- Energy Efficiency: The NCS4K-AC-PSU is designed to be energy efficient, which can help to reduce power consumption and costs.
- Reliability: The NCS4K-AC-PSU is designed to be reliable and durable, which can help to ensure that the network system remains operational even in case of power supply failure.
- Easy Installation: The NCS4K-AC-PSU can be easily installed, which can help to minimize downtime and ensure that the network system is up and running quickly.
- Compatibility: The NCS4K-AC-PSU is designed to be compatible with the Cisco Network Convergence System 4200 Series, which can help to ensure seamless integration and operation.
General Information
- Manufacturer Cisco Systems, Inc
- Manufacturer Part Number NCS4K-AC-PSU
- Product Name NCS 4016 AC Power Module
- Product Type Power Module
Power Description
- Output Power 3000 W
