Description
Installation and Setup
The BV897A HPE 2Port 1GB Ethernet Module is a hardware component that can be installed in certain HPE switches to expand their network connectivity capabilities. Here are the steps to install and set up this module:
- Turn off the HPE switch and unplug all cables from it.
- Remove the switch’s cover by unscrewing it or releasing any latches that hold it in place.
- Locate an available slot on the switch’s motherboard where the BV897A module can be installed. Depending on the switch model, this slot may be labeled as an “Expansion slot” or a “Module slot.”
- Carefully align the BV897A module with the slot, making sure that the connectors on the module’s bottom side are aligned with the corresponding connectors on the slot.
- Push the module gently but firmly into the slot until it clicks into place. Ensure that the module is seated firmly and securely.
- Re-attach the switch’s cover and screw it back into place or latch it down.
- Connect the Ethernet cables to the ports on the BV897A module.
- Turn on the HPE switch and wait for it to boot up.
- Access the switch’s command-line interface (CLI) or web-based management interface.
- Configure the BV897A module by assigning IP addresses, VLANs, and other network settings to its ports using the appropriate commands or menus in the management interface.
- Verify that the BV897A module is functioning correctly by running diagnostic tests or pinging devices connected to its ports.
Note: These steps are general guidelines, and the exact installation and setup process may vary depending on the specific HPE switch model and the firmware version it is running. Always consult the switch’s documentation and follow the manufacturer’s instructions carefully.
The BV897A HPE 2Port 1GB Ethernet Module is an expansion module that provides additional Ethernet connectivity to compatible HPE switches. While the module itself does not have a user interface or controls, its functionality can be managed through the switch’s management interface.
Once the module is installed in the switch, it will appear as two additional Ethernet ports in the switch’s interface. These ports can be configured like any other Ethernet port on the switch.
The switch’s management interface typically provides a range of options for configuring the module and its ports, including setting speed and duplex mode, enabling VLAN tagging, configuring link aggregation, and monitoring port status and traffic.
Performance and Efficiency
The BV897A HPE 2Port 1GB Ethernet Module is a network interface card designed to provide high-speed connectivity to HPE servers. It offers two ports for connecting to Ethernet networks, each capable of delivering data at up to 1 gigabit per second (Gbps) speed.
In terms of performance, the BV897A module provides reliable and high-speed data transfer, making it ideal for use in data-intensive applications such as video streaming, data backup, and database management. It is also designed to handle high traffic loads and support advanced network features such as jumbo frames and link aggregation, which can further improve network performance.
In addition to performance, the BV897A module is also designed for efficiency. It features Energy Efficient Ethernet (EEE) technology, which reduces power consumption during periods of low network activity, resulting in lower energy costs and a reduced carbon footprint. The module also supports Wake-on-LAN (WoL) functionality, which allows network administrators to remotely wake up a server from a sleep or hibernate state, reducing energy consumption and improving operational efficiency.
General Information
- Device Type : Network Adapter – 2 Ports
- Interface (Bus) Type : Pci Express X4
- Pci Specification Revision : Pcie 1.0
Networking
- Connectivity Technology : Wired
- Data Link Protocol : Gigabit Ethernet
- Data Transfer Rate : 1 Gbps
- Network / Transport Protocol : Tcp/Ip
- Features : Vlan Support, Wake On Lan (Wol), Ipv6 Support, Tcp/Ip Offloading, Quality Of Service (Qos), Jumbo Frames Support
- Compliant Standards : IEEE 802.3, IEEE 802.1q, IEEE 802.1p, IEEE 802.3x, IEEE 802.3ad (Lacp)
Expansion / Connectivity
- Interfaces : 2 X Network





