Description
Ethernet Connectivity with the NM-1FE1R2W
The NM-1FE1R2W is a network module for Cisco routers that provides a combination of Ethernet, Token-Ring, and WAN connectivity. Specifically, it includes one 10/100 Ethernet port, four or sixteen Token-Ring ports (depending on the version), and two WAN card slots. Here’s how to set up Ethernet connectivity with this module:
- Choose the Ethernet port: The NM-1FE1R2W includes one 10/100 Ethernet port, so you’ll need to choose which port you want to use for Ethernet connectivity.
- Connect the Ethernet cable: Connect one end of an Ethernet cable to the chosen Ethernet port on the NM-1FE1R2W and the other end to a switch or another network device with an Ethernet port.
- Configure the Ethernet port: In order to use the Ethernet port on the NM-1FE1R2W, you’ll need to configure it using the Cisco router’s CLI (command-line interface). This typically involves assigning an IP address to the port and configuring any necessary routing protocols or access control lists.
- Verify connectivity: After configuring the Ethernet port, you can test connectivity by pinging other devices on the network or by using tools like traceroute to trace the path of packets through the network.
WAN Connectivity with the NM-1FE1R2W
The NM-1FE1R2W is a network module for Cisco 2600, 3600, and 3700 series routers. This module provides one 10/100 Ethernet port, two 4/16 Token-Ring ports, and two WAN card slots. Here’s how you can set up WAN connectivity with this module:
- Choose a WAN interface card (WIC): The NM-1FE1R2W module has two WIC slots, which you can use to install a variety of WAN interface cards, depending on your network requirements. Some examples of WICs that you can use include the WIC-1T, WIC-2T, WIC-1DSU-T1, and WIC-2A/S.
- Install the WIC: Insert the WIC into one of the two WIC slots on the NM-1FE1R2W module. Make sure to align the card with the guide rails and firmly press it in until it clicks into place.
- Connect the WAN cable: Connect the WAN cable to the WIC port on the NM-1FE1R2W module. The type of cable you need will depend on the specific WIC you’re using and the type of WAN connection you’re making (e.g. T1, E1, ISDN, etc.).
- Configure the WAN interface: Once you’ve installed the WIC and connected the WAN cable, you’ll need to configure the WAN interface in your router’s configuration. This will involve setting the encapsulation type, configuring the IP address and subnet mask, and specifying any other relevant settings for your specific WAN connection.
- Test the connection: Finally, test the connectivity of your WAN connection by sending traffic through it and verifying that it’s being processed correctly. You can use tools like ping or traceroute to test network connectivity.
Compatibility with Cisco Routers
The NM-1FE1R2W is a network module designed for use with Cisco 2600, 3600, and 3700 series routers. This module provides one 10/100 Ethernet port, one 4/16 Token-Ring port, and two WAN card slots, allowing you to connect to a variety of network types and protocols. Here’s a summary of the compatibility of the NM-1FE1R2W module:
- Compatibility with Cisco routers: The NM-1FE1R2W module is compatible with Cisco 2600, 3600, and 3700 series routers. However, it’s important to note that the module may not be compatible with certain hardware or software configurations, so it’s always a good idea to check the compatibility matrix provided by Cisco for your specific router and module combination.
- Compatibility with network protocols: The Ethernet port on the NM-1FE1R2W module supports the 10/100 Mbps Ethernet standard, which is a widely used networking protocol. The Token-Ring port supports both 4 Mbps and 16 Mbps Token-Ring protocols, which are less commonly used than Ethernet but may still be in use in certain networks. The module also has two WAN card slots, which can support a variety of WAN technologies such as T1, ISDN, and Frame Relay.
- Compatibility with software releases: The NM-1FE1R2W module is compatible with a wide range of software releases for the Cisco routers it supports. However, compatibility should always be verified with the specific hardware and software configuration being used.
General Information
- Manufacturer: Cisco Systems, Inc
- Manufacturer Part Number: NM-1FE1R2W
- Brand Name: Cisco
- Product Name: 1-Port 10by100 Ethernet 1-Port Token Ring 2 WIC Slots Network Module
- Product Type: Network Module
Technical Information
- Application/Usage Data Networking
Interfaces/Ports
- Interfaces/Ports Details 1 x RJ-45 10/100Base-TX LAN
- Interfaces/Ports Details 1 x RJ-45 Token Ring LAN
- Interfaces/Ports Details 1 x DB-9 Token Ring LAN
Media & Performance
- Media Type Supported Twisted Pair
- Ethernet Technology Fast Ethernet
- Network Technology Token Ring
- Network Technology 10/100Base-TX
- Maximum Data Transfer Rate 100 Mbit/s
I/O Expansions
- Number of Total Expansion Slots 2
- Expansion Slot Type WIC
- Expansion Slot Type VWIC
Memory
- Memory Technology DDR SDRAM
Please contact us over the phone or ask for live chat/help if you have any questions about the estimated time of arrival for any “lead time required” item.
