CK614 Dell Controller Md1000 Enclosure Management Module SAS/SATA. Refurbished.

For bulk orders contact sales via email sales@allhdd.com, via chat, or call our toll-free number 1-800-675-5044.

CK614 Dell Controller Md1000 Enclosure Management Module SAS/SATA. Refurbished.

$46.00

1 in stock

SKU: CK614 Category: SAS-SATA Brand: Dell

Description

Technical Specifications of the CK614 Dell Controller

The CK614 Dell Controller is a management module designed to support the Dell PowerVault MD1000 SAS/SATA disk array. The technical specifications of the CK614 Dell Controller include:

Compatibility: The CK614 Dell Controller is compatible with the Dell PowerVault MD1000 disk array.
Interfaces: The controller supports SAS and SATA interfaces for connectivity to the disk array.
Management: The CK614 Dell Controller provides enclosure management for the MD1000 disk array, including system monitoring, fault detection, and reporting.
RAID support: The controller supports RAID levels 0, 1, 5, 6, 10, 50, and 60 for data redundancy and protection.
Power supply: The controller requires a 12V DC input power supply.
Environmental specifications: The CK614 Dell Controller is designed to operate in a temperature range of 5°C to 40°C and at a relative humidity range of 20% to 80% non-condensing.
Dimensions: The controller has dimensions of 1.1 x 7.3 x 6.5 inches (2.79 x 18.54 x 16.51 cm).
Weight: The controller weighs approximately 1 pound (0.45 kg).
LED indicators: The CK614 Dell Controller includes LED indicators for system status, power, and fault detection.
Firmware: The controller firmware can be upgraded through a web-based user interface or command line interface.

Installation and Configuration of the CK614 Dell Controller

Here are the steps to install and configure the CK614 Dell Controller:

Turn off the Dell PowerVault MD1000 disk array and unplug it from the power source.
Remove the top cover of the MD1000 disk array by loosening the screws on the top panel.
Locate the slot where the CK614 Dell Controller will be installed. It is usually located on the left-hand side of the disk array.
Remove the filler panel from the slot by pulling the release lever and sliding it out.
Carefully insert the CK614 Dell Controller into the slot and push it in until it clicks into place.
Replace the top cover of the MD1000 disk array and secure it with the screws.
Plug in the MD1000 disk array to the power source and turn it on.
Wait for the MD1000 disk array to boot up and detect the CK614 Dell Controller.
Access the CK614 Dell Controller management interface using a web browser or command line interface.
Configure the controller settings according to your needs. This may include setting up RAID levels, configuring system monitoring, and setting up notifications for system alerts.
Save the configuration settings and exit the management interface.
Monitor the system and test the CK614 Dell Controller functionality to ensure that it is working properly.

By following these steps, you can successfully install and configure the CK614 Dell Controller for use with your Dell PowerVault MD1000 disk array.

Troubleshooting Common Issues with the CK614 Dell Controller

Here are some common issues you may encounter when using the CK614 Dell Controller with the MD1000 disk array, as well as some troubleshooting tips:

Device not recognized: If the device is not recognized by your system, check that the CK614 controller is properly installed and connected to the MD1000 disk array.
Poor performance: If you are experiencing poor performance, check that the CK614 controller is properly configured and that the drivers are up to date. You can also try optimizing the controller settings for your specific workload.
Overheating: If the CK614 controller is overheating, ensure that the ventilation in the server room is adequate and that the air filters in the server are clean.
Disk failures: If disks are failing or producing errors, check that the disks are properly installed and that they are supported by the CK614 controller.
Incompatibility issues: If you are experiencing compatibility issues, ensure that the CK614 controller is compatible with the device or software you are trying to use.
Firmware issues: If you are experiencing firmware issues, make sure that the firmware is up to date and that you are using the latest drivers and software.

If you continue to experience issues with the CK614 Dell Controller, consult the documentation provided by Dell or contact their customer support team for assistance. They can help you troubleshoot the issue and provide guidance on resolving any problems you may encounter.

General Information