701530-001 HPE Flexfabric 10GB Ethernet PCI Express 2.0X8 Refurbished

The HPE Flexfabric 10GB Ethernet PCI Express 2.0X8 Network Adapter can be installed on compatible ProLiant Gen8 servers to provide high-speed network connectivity. Here are some general steps for installing the adapter:

• Ensure that your ProLiant Gen8 server meets the system requirements for the adapter, including any hardware or software prerequisites.
• Power down the server and disconnect all cables and accessories.
• Locate an available PCIe slot on the server where you want to install the adapter. Refer to the server documentation for the appropriate slot type and location.
• Remove the cover from the server case and locate the selected PCIe slot.
• Remove the protective cover from the PCIe slot and carefully insert the adapter into the slot. Press down gently but firmly until the adapter is securely in place.
• Replace the cover on the server case and reconnect all cables and accessories.
• Power on the server and log in to the operating system.
• Install the appropriate drivers for the adapter, which may be provided on a CD or available for download from the HPE website.
• Follow the prompts to install the drivers and configure the adapter for your network.
• Verify that the adapter is recognized by the operating system and that the network connection is functioning properly.

These are general steps and the specific installation process may vary depending on the particular ProLiant Gen8 server and adapter configuration. It is recommended to consult the manufacturer's documentation and follow the installation instructions carefully to ensure a successful installation.

The HPE Flexfabric 10GB Ethernet PCI Express 2.0X8 Network Adapter has some limitations and constraints that should be considered when selecting and using the adapter:

• Compatibility: The adapter is designed to work with HPE ProLiant Gen8 servers and may not be compatible with other server models or hardware configurations.
• Operating system support: The adapter is supported on a limited number of operating systems, including Windows, Linux, and VMware ESXi.
• PCIe bus limitations: The adapter uses a PCIe 2.0 x8 interface, which can limit the amount of bandwidth available for other PCIe devices on the server.
• Network constraints: The adapter's 10GB Ethernet connectivity requires a compatible network infrastructure and may not be compatible with older network equipment or cabling.
• Power consumption: The adapter can consume significant power, which may impact the overall power consumption and cooling requirements of the server.
• System configuration limitations: The adapter may require certain system configurations, such as a minimum amount of available memory or a specific BIOS version, to function properly.
• Performance limitations: The adapter's performance may be limited by the server's hardware capabilities, the network infrastructure, or other factors.

These limitations and constraints should be considered when selecting and using the HPE Flexfabric adapter. It is recommended to consult the manufacturer's documentation and work with a network administrator or IT professional to ensure that the adapter is compatible with the server environment and to optimize its performance and functionality within that environment.

Troubleshooting common issues with the HPE Flexfabric 10GB Ethernet PCI Express 2.0X8 Network Adapter is an important aspect of maintaining its proper functioning within the server environment. Here are some common issues and general troubleshooting steps:

• Network connectivity issues: If the adapter is not connecting to the network, check the adapter configuration to ensure that it has been properly configured with the correct IP address, subnet mask, gateway, and DNS server settings. Additionally, check that the network cable is properly connected and that the switch port and cable are functioning properly.
• Slow network performance: If the adapter is connected to the network but experiencing slow performance, check for any network congestion, QoS misconfigurations, or any other factors that could be impacting network performance. Additionally, ensure that the server hardware is capable of handling the network traffic load and that the network adapter is properly configured for optimal performance.
• Driver or firmware issues: If the adapter is not working properly, ensure that the correct drivers and firmware are installed and up-to-date. You can download the latest drivers and firmware from the HPE website or other sources.
• Power or temperature issues: If the adapter is experiencing power or temperature issues, ensure that the server is properly cooled and that the power supply is adequate to support the adapter and any other components in the server.
• Physical damage or failure: If the adapter is physically damaged or not functioning properly, it may need to be replaced. Check for any visible signs of damage, such as bent pins or scorch marks on the adapter or server motherboard.

These are general troubleshooting steps and the specific issues and solutions may vary depending on the particular server environment and operating system. It is recommended to consult the manufacturer's documentation and work with a network administrator or IT professional to identify and troubleshoot any issues with the HPE Flexfabric adapter.

Main Features

• Manufacturer: HPE
• MPN: 701530-001
• Spare Part Number: 700748-B21
• Adapter Type: Network Adapter
• Form Factor: Plug-in card
• Interface (Bus) Type: PCI Express 2.0 x8
• PCI Specification Revision: PCIe 2.0

• Ports: 10Gb Ethernet x 2
• Connectivity Technology: Wired
• Data Link Protocol: 10 GigE
• Data Transfer Rate: 10 Gbps
• Features: TCP/IP offloading, Quality of Service (QoS), Jumbo Frames support, PXE support, Single Root I/O Virtualization (SR-IOV), tagged VLAN, TCP Offload Engine (TOE)
• Compliant Standards: IEEE 802.3, IEEE 802.3u, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.3ae, IEEE 802.3p, IEEE 802.3ap

• Processor: 1 x BCM57810S - Broadcom
• RAM: 900 MB

Expansion/Connectivity

• Interfaces: 2 x 10Gb Ethernet

• Compliant Standards: FCC Class A certified, UL, BSMI CNS 13438 Class A, EN55022 Class A, WEEE, RoHS, FCC Part 15 A, AS/NZS, VCCI V-3 Class A ITE, EN 61000-3-2:2006, EN 61000-3-3:2008, ICES-003 issue 4 Class A, KN24, KN22 Class A, EN55024:1998 + A1 + A2

• OS Required: SunSoft Solaris 10, Microsoft Windows Server 2008 R2, Microsoft Windows Server 2008, SuSE Linux Enterprise Server 11 SP1, Red Hat Enterprise Linux 6.1, Red Hat Enterprise Linux 5.7, SuSE Linux Enterprise Server 10 SP4, Microsoft Windows Server 2012, VMware vSphere 5.0, VMware vSphere 4.1

• Min Operating Temperature: 32 °F
• Max Operating Temperature: 131 °F
• Humidity Range Operating: 10 - 90% (non-condensing)

• HPE ProLiant BL420c Gen8, BL460c Gen8, BL465c Gen8, BL660c Gen8, BL660c Gen8 Performance, WS460c Gen9 Graphics, WS460c Gen9 Graphics Expansion